In this paper, we propose a channel-unaware algorithm to suppress the narrowband interference (NBI) for the time synchronization, where multiple antennas are equipped at the receiver. Based on the fact that the characteristics of synchronization signal are different from those of NBI in both the time and spatial domain, the proposed algorithm suppresses the NBI by utilizing the multiple receive antennas in the eigen domain of NBI, where the eigen domain is obtained from the time domain statistical information of NBI. Because time synchronization involves incoherent detection, the proposed algorithm does not use the desired channel information, which is different from the eigen domain interference rejection combining (E-IRC). Simulation results show, compared with the traditional frequency domain NBI suppression technique, the proposed algorithm has about a 2 dB gain under the same probability of detection.

Provisioning multiple paths can improve fault tolerance and transport capability of multi-routing in wireless networks. Disjoint paths can improve the diversity of paths and further reduce the risk of simultaneous link failure and network congestion. In this paper we first address a many-to-one disjoint-path problem (MOND) for multi-path routing in a multi-hop wireless network. The objective of this problem is to maximize the minimum number of disjoint paths of every source to the destination. We prove that it is NP-hard to obtain k disjoint paths for every source when k ≥ 3. To solve this problem efficiently, we propose a heuristic algorithm called TOMAN based on network flow theory. Experimental results demonstrate that it outperforms three related algorithms.

The Network-on-Chip (NoC) is limited by the reliability constraint, which impels us to exploit the fault-tolerant routing. Generally, there are two main design objectives: tolerating more faults and achieving high network performance. To this end, we propose a new multiple-round dimension-order routing (NMR-DOR). Unlike existing solutions, besides the intermediate nodes inter virtual channels (VCs), some turn-legally intermediate nodes inside each VC are also utilized. Hence, more faults are tolerated by those new introduced intermediate nodes without adding extra VCs. Furthermore, unlike the previous solutions where some VCs are prioritized, the NMR-DOR provides a more flexible manner to evenly distribute packets among different VCs. With extensive simulations, we prove that the NMR-DOR maximally saves more than 90% unreachable node pairs blocked by faults in previous solutions, and significantly reduces the packet latency compared with existing solutions.

Web application second-order vulnerabilities first inject malicious code into the persistent data stores of the web server and then execute it at later sensitive operations, causing severe impact. Nevertheless, the dynamic features, the complex data propagation, and the inter-state dependencies bring many challenges in discovering such vulnerabilities. To address these challenges, we propose DISOV, a web application property graph (WAPG) based method to discover second-order vulnerabilities. Specifically, DISOV first constructs WAPG to represent data propagation and inter-state dependencies of the web application, which can be further leveraged to find the potential second-order vulnerabilities paths. Then, it leverages fuzz testing to verify the potential vulnerabilities paths. To verify the effectiveness of DISOV, we tested it in 13 popular web applications in real-world and compared with Black Widow, the state-of-the-art web vulnerability scanner. DISOV discovered 43 second-order vulnerabilities, including 23 second-order XSS vulnerabilities, 3 second-order SQL injection vulnerabilities, and 17 second-order RCE vulnerabilities. While Black Widow only discovered 18 second-order XSS vulnerabilities, with none second-order SQL injection vulnerability and second-order RCE vulnerability. In addition, DISOV has found 12 0-day second-order vulnerabilities, demonstrating its effectiveness in practice.

LSI testing is critical to guarantee chips are fault-free before they are integrated in a system, so as to increase the reliability of the system. Although full-scan is a widely adopted design-for-testability technique for LSI design and testing, there is a strong need to reduce the test data Volume, scan-in Power dissipation, and test application Time (VPT) of full-scan testing. Based on the analysis of the characteristics of the variable-to-fixed run-length coding technique and the random access scan architecture, this paper presents a novel design scheme to tackle all VPT issues simultaneously. Experimental results on ISCAS'89 benchmarks have shown on average 51.2%, 99.5%, 99.3%, and 85.5% reduction effects in test data volume, average scan-in power dissipation, peak scan-in power dissipation, and test application time, respectively.

In 3GPP (3rd Generation Partnership Project) LTE (Long Term Evolution) systems, when HARQ (Hybrid Automatic Repeat request) retransmission is invoked, the data at the transmitter are retransmitted randomly or sequentially regardless of their relationship to the wrongly decoded data. Such practice is inefficient since precious transmission resources will be spent to retransmit data that may be of no use in error correction at the receiver. This paper proposes an incremental redundancy HARQ scheme based on Error Position Estimating Coding (ePec) and LDPC (Low Density Parity Check Code) channel coding, which is called ePec-LDPC HARQ. The proposal is able to feedback the wrongly decoded code blocks within a specific MAC (Media Access Control) PDU (Protocol Data Unit) from the receiver. The transmitter gets the feedback information and then performs targeted retransmission. That is, only the data related to the wrongly decoded code blocks are retransmitted, which can improve the retransmission efficiency and thus reduce the retransmission overload. An enhanced incremental redundancy LDPC coding approach, called EIR-LDPC, together with a physical layer framing method, is developed to implement ePec-LDPC HARQ. Performance evaluations show that ePec-LDPC HARQ reduces the overall transmission resources by 15% compared to a conventional LDPC HARQ scheme. Moreover, the average retransmission times of each MAC PDU and the transmission delay are also reduced considerably.

In the framework of the modernization plan of COMPASS system, the existing COMPASS signals should be transmitted along with the modernized signals to maintain backward compatibility. In this paper, an efficient multiplexing scheme based on the optimal aligning method for combining COMPASS Phase II B3 and Phase III B3 signals is proposed, which offers significantly higher efficiency than Interplex and Generalized Majority Voting (GMV) multiplexing methods. The proposed scheme can provide potential opportunities for COMPASS system and other global navigation satellite systems (GNSS) modernization and construction plans.

Electromagnetic scattering properties of metamaterial cylinders due to a line source are studied by a multilayer algorithm based on eigenfunctional expansion. Closed forms of electric and magnetic fields are formulated. Both the fields inside the cylinder and field in outer space are plotted for different sizes of the cylinder. The focusing phenomena and the wave propagation in the presence of metamaterial cylinders are investigated and shown. Electromagnetic field distributions are presented for subwavelength metamaterial cylinders and cylinders fabricated by magnetoelectric materials, and resonant scattering and focusing properties are reported. Special designs of scatterer cloaking are proposed and calculated by multilayer algorithm which can reduce scattering cross sections.

The element-by-element finite element method (EBE-FEM) combined with the preconditioned conjugate gradient (PCG) technique is employed in this paper to calculate the coupling capacitances of multi-level high-density three-dimensional interconnects (3DIs). All capacitive coupling 3DIs can be captured, with the effects of all geometric and physical parameters taken into account. It is numerically demonstrated that with this hybrid method in the extraction of capacitances, an effective and accurate convergent solution to the Laplace equation can be obtained, with less memory and CPU time required, as compared to the results obtained by using the commercial FEM software of either MAXWELL 3D or ANSYS.

Resulting from the spread of Mobile Internet, the mobile communication with QoS guarantee will be required in order to realize mobile video interactions. So far, there are some studies focusing on QoS Mobile IP communication, but they require backbone routers to maintain per-flow QoS information for all individual Mobile Nodes. So these approaches suffer from the lack of scalability. Against them, we are developing an approach which the per-flow QoS information is maintained only by Mobile IP agents such as the Home Agent and the Foreign Agent. We have adopted a hierarchical method with MPLS which MPLS paths with large bandwidth are introduced between Mobile IP related nodes, and a per-flow path with small bandwidth called Pathlet is established for individual communication between a Mobile Node and a Fixed Host. The maintenance of Pathlets is only performed by Home Agent, Foreign Agent and Fixed Host, and the network backbone MPLS routers only take care of MPLS paths with large bandwidth. In the simulation, we compare our scheme with conventional scheme by observing the total number of entries managed by routers and bandwidth prepared at individual links.

Automatic disassembly of railway fasteners is of great significance for improving the efficiency of replacing rails. The accurate positioning of fastener is the key factor to realize automatic disassembling. However, most of the existing literature mainly focuses on fastener region positioning and the literature on accurate positioning of fasteners is scarce. Therefore, this paper constructed a visual inspection system for accurate positioning of fastener (VISP). At first, VISP acquires railway image by image acquisition subsystem, and then the subimage of fastener can be obtained by coarse-to-fine method. Subsequently, the accurate positioning of fasteners can be completed by three steps, including contrast enhancement, binarization and spike region extraction. The validity and robustness of the VISP were verified by vast experiments. The results show that VISP has competitive performance for accurate positioning of fasteners. The single positioning time is about 260ms, and the average positioning accuracy is above 90%. Thus, it is with theoretical interest and potential industrial application.

A monolithic frequency synthesizer with wide tuning range, low phase noise and spurs was realized in 0.13,$mu$m CMOS technology. It consists of an analog PLL, a harmonic-rejection mixer and injection-locked frequency doublers to cover the whole 6--18,GHz frequency range. To achieve a low phase noise performance, a sub-sampling PLL with non-dividers was employed. The synthesizer can achieve phase noise $-$113.7,dBc/Hz@100,kHz in the best case and the reference spur is below $-$60,dBc. The core of the synthesizer consumes about 110,mA*1.2,V.

In this paper, the thermal characteristic of the GaN HFETs has been analyzed using the hybrid finite element method (FEM). Both the steady and transient state thermal operations are quantitatively studied with the effects of temperature-dependent thermal conductivities of GaN and the substrate materials properly treated. The temperature distribution and the maximum temperatures of the HFETs operated under excitations of continuous-waves (CW) and pulsed-waves (PW) including double exponential shape PW such as electromagnetic pulse (EMP) and ultra-wideband (UWB) signal are studied and compared.

A full-duplex radio-on-fiber (ROF) transport system based on optical single sideband (SSB) modulation, wavelength-division-multiplexing (WDM) and optical add-drop multiplexing techniques is proposed and demonstrated. A 1.5-dB RF power degradation due to the chromatic dispersion was achieved by employing optical SSB modulation scheme in the system, in which resulting in low bit error rate (BER) and third order intermodulation distortion to carrier ratio (IMD3/C) values. Such a proposed full-duplex ROF transport system is suitable for the long-haul microwave optical link.

In order to improve tracking, interference and multipath mitigation performance from that possible with existing signals, a new Global Navigation Satellite System (GNSS) signal is needed that can offer additional degrees of freedom for shaping its pulse waveform and spectrum. In this paper, a new modulation scheme called Quinary Offset Carrier modulation (QOC) is proposed as a new GNSS signal design. The pulse waveforms of QOC modulation are divided into two types: convex and concave waveforms. QOC modulations can be easily constructed by selecting different modulation parameters. The spectra and autocorrelation characteristics of QOC modulations are investigated and discussed. Simulations and analyses show that QOC modulation can achieve similar performance to traditional BOC modulation in terms of code tracking, anti-multipath, and compatibility. QOC modulation can provide a new option for satellite navigation signal design.

The widespread application of mobile electronic devices has triggered a boom in energy consumption, especially in user equipment (UE). In this paper, we investigate the energy-efficiency (EE) of a UE experiencing the worst channel conditions, which is termed worst-EE. Due to the limited battery of the mobile equipment, worst-EE is a suitable metric for EE fairness optimization in the uplink transmissions of orthogonal frequency division multiple access (OFDMA) networks. More specifically, we determine the optimal power and sub-carrier allocation to maximize the worst-EE with respect to UEs' transmit power, sub-carriers and statistical quality-of-service (QoS). In order to maximize the worst-EE, we formulate a max-min power and sub-carrier allocation problem, which involves nonconvex fractional mixed integer nonlinear programming, i.e., NP-hard to solve. To solve the problem, we first relax the allocation of sub-carriers, formulate the upper bound problem on the original one and prove the quasi-concave property of objective function. With the aid of the Powell-Hestenes-Rockfellar (PHR) approach, we propose a fairness EE sub-carrier and power allocation algorithm. Finally, simulation results demonstrate the advantages of the proposed algorithm.

A new pixel design and driving method for active matrix organic light emitting diode (AMOLED) displays that use low-temperature polycrystalline silicon thin-film transistors (LTPS-TFTs) with a voltage programming method are proposed and verified using the SPICE simulator. We had employed an appropriate TFT model in SPICE simulation to demonstrate the performance of the pixel circuit. The OLED anode voltage variation error rates are below 0.35% under driving TFT threshold voltage deviation (Δ Vth = 0.33 V). The OLED current non-uniformity caused by the OLED threshold voltage degradation (Δ VTO = +0.33 V) is significantly reduced (below 6%). The simulation results show that the pixel design can improve the display image non-uniformity by compensating for the threshold voltage deviation in the driving TFT and the OLED threshold voltage degradation at the same time.

To tackle the distributed power optimization problems in wireless sensor networks localization systems, we model the problem as a hierarchical game, i.e. a multi-leader multi-follower Stackelberg game. Existing researches focus on the power allocation of anchor nodes for ranging signals or the power management of agent nodes for cooperative localization, individually. However, the power optimizations for different nodes are indiscerptible due to the common objective of localization accuracy. So it is a new challenging task when the power allocation strategies are considered for anchor and agent nodes simultaneously. To cope with this problem, a hierarchical game is proposed where anchor nodes are modeled as leaders and agent nodes are modeled as followers. Then, we prove that games of leaders and followers are both potential games, which guarantees the Nash equilibrium (NE) of each game. Moreover, the existence of Stackelberg equilibrium (SE) is proved and achieved by the best response dynamics. Simulation results demonstrate that the proposed algorithm can have better localization accuracy compared with the decomposed algorithm and uniform strategy.

Mobile virtual network operators (MVNOs) are mobile operators without their own infrastructure or government issued spectrum licenses. They purchase spectrum resources from primary mobile network operators (MNOs) to provide communication services under their own brands. MVNOs are expected to play an important role in mobile network markets, as this will increase the competition in retail markets and help to meet the demand of niche markets. However, with the rapidly increasing demand of mobile data traffic, efficient utilization of the limited spectrum resources owned by MVNOs has become an important issue. We propose here a resource sharing mechanism between MVNOs against the background of network functions virtualization (NFV). The proposed mechanism enables MVNOs to improve their quality of service (QoS) by sharing spectrum resources with each other. A nash bargaining solution based decision strategy is also devised to ensure the fairness of resource sharing. Extensive numerical evaluation results validate the effectiveness of the proposed models and mechanisms.

A 19.1-to-20.4 GHz sigma-delta fractional-N frequency synthesizer with two-point modulation (TPM) for frequency modulated continuous wave (FMCW) radar applications is presented. The FMCW synthesizer proposes a digital and voltage controlled oscillator (D/VCO) with large continuous frequency tuning range and small digital controlled oscillator (DCO) gain variation to support TPM. By using TPM technique, it avoids the correlation between loop bandwidth and chirp slope, which is beneficial to fast chirp, phase noise and linearity. The start frequency, bandwidth and slope of the FMCW signal are all reconfigurable independently. The FMCW synthesizer achieves a measured phase noise of -93.32 dBc/Hz at 1MHz offset from a 19.25 GHz carrier and less than 10 µs locking time. The root-mean-square (RMS) frequency error is only 112 kHz with 94 kHz/µs chirp slope, and 761 kHz with a fast slope of 9.725 MHz/µs respectively. Implemented in 65 nm CMOS process, the synthesizer consumes 74.3 mW with output buffer.